The BMW of 3 series Е46
+ Cars BMW 3 (Е46)
+ Current leaving and service
+ The engine
+ Systems of cooling, heating
+ Power supply systems, injection and release
+ Engine electric equipment
+ manual transmission and трансмиссионная a line
+ Automatic transmission
+ Coupling and power shafts
+ Brake system
- Suspension bracket and steering
+ Forward suspension bracket
- Back suspension bracket
Removal and installation of the back shock-absorber
Removal and installation of springs of a suspension bracket
+ Steering with the hydraulic booster (сервоуправление)
+ Body
+ Onboard electric equipment
+ Electric equipment schemes
|
Removal and installation of the back shock-absorber
The shock-absorber, spring of a suspension bracket and shock-absorber support
|
1 — a nut, 15 Н•м
Self-stopped, necessarily replace
2 — a plate
3 — a nut with a fillet, 25 Н•м
Self-stopped, necessarily replace
4 — a plate intensifying
Only for a car left-hand side
5 — a sealing plate
6 — a bolt
7 — a shock-absorber support
8 — a plate |
9 — a remote washer
10 — plastic демпфер
11 — a pipe protective
12 — the shock-absorber back
13 — bolt М12, 100 Н•м
14 — a spring cup top
15 — a suspension bracket spring
16 — a spring cup bottom
17 — an adapter
18 — the plastic buffer |
|
1 Take away facing of a luggage compartment around shock-absorber fastening.
|
Operation of lifting and car installation on supports is connected with danger! Therefore before operation carrying out familiarise with Razdelom Poddomkrachivanie and towage |
2 Lift and establish on supports a back part of the car.
|
3 Prop up the bottom cross-section lever-4 garage lift, having enclosed a wooden lining.
|
If this condition is not carried out, the suspension bracket beam will fall after a shock-absorber detachment downwards. The power shaft can be thus damaged. |
|
4 Disconnect the shock-absorber-1 at a suspension bracket beam. Mark position of both washers for possibility of the subsequent assemblage. The persistent washer shows-3 rubber support towards a head of a bolt-2.
|
5 Turn on two nuts of fastening of an aligning cup. |
6 Remove an intensifying plate if it is available, on a car left-hand side.
7 Take out downwards the shock-absorber.
|
The shock-absorber hold only vertically. Otherwise during car movement there can be a raised noise. Then it is necessary to extend a rod and to put the shock-absorber at 24 o'clock at a room temperature (+20С). |
|
|
|
8 Check up the shock-absorber, address to Section Removal and installation of the back shock-absorber.
9 Lining between the shock-absorber and a body necessarily replace with the new.
10 Insert the shock-absorber.
11 Insert an intensifying plate if she acted in film.
12 Fix the shock-absorber above two new self-stopped nuts and tighten their moment 25 Н•м.
13 Fix the shock-absorber below, without tightening while a fastening nut. Do not forget to put thus a washer from both parties of fastening of the shock-absorber. The persistent washer of a rubber support should show towards a bolt head.
14 Take away the garage lift and lower the car on wheels.
15 At a tightening of a nut of fastening of the bottom support of the shock-absorber the car should not be loaded. Following conditions should be for this purpose satisfied:
— The car is completely filled by fuel;
— мдавление in tyres in to correspond to the established;
— The car has the following scheme of loading: 2 Х 68 kg in front, 1Х 68 kg behind, 1 Х 21 kg in the luggage carrier centre;
— Car suspension brackets прожаты.
16 Tighten the bottom bolt of fastening by the moment 100 Н•м.
17 Close a cover of a luggage compartment. |
|
|
|