BMW 3 series E46

Since 1998 of release

Repair and car operation



The BMW of 3 series Е46
+ Cars BMW 3 (Е46)
+ Current leaving and service
+ The engine
+ Systems of cooling, heating
- Power supply systems, injection and release
   Security measures and rules of observance of cleanliness at work with fuel system
   Removal and installation of the gauge of a stock of fuel / the fuel pump
   Check of the gauge of a stock of fuel
   + The power supply system of petrol engines
   + System of injection of fuel of the petrol engine
   + The power supply system of diesel engines
   + System of release of the fulfilled gases
+ Engine electric equipment
+ manual transmission and трансмиссионная a line
+ Automatic transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
+ Electric equipment schemes





Removal and installation of the gauge of a stock of fuel / the fuel pump

At car BMW of 3rd series the gauge of a stock of fuel is located in each chamber of a fuel tank. For check of gauges they are necessary for removing. In the gauge of the right chamber, at a sight in a movement direction, there is a fuel pump. Therefore for pump removal it is necessary to remove the right gauge.

- Do not use near to a workplace open fire, do not smoke and do not hold any strongly разогретых subjects. There is a danger of accident! Keep in readiness the fire extinguisher.
- Watch normal ventilation of a workplace. Fuel steams are poisonous.
- The fuel system is under pressure. At opening of system fuel can be pulled out under pressure. Collect fuel a rag. Use goggles.


 REMOVAL

Before removal of the fuel pump empty a fuel tank, having passed on the car. Works whenever possible should be spent in the open air and at good ventilation. The radial fan which electric motor is located outside of an air stream can be applied to workplace ventilation also.

1 Disconnect a negative cable (-) the storage battery at the switched off ignition. The battery is in a luggage compartment behind a cover on the right side. At cars BMW 316i, 318i the battery settles down in an impellent compartment.

As a result of switching-off of the storage battery the data from memory of malfunctions of some monitors is erased. If necessary before battery switching-off it is necessary to consider the given memories of malfunctions. Address to Section Diagnostics of malfunctions. Work it is desirable to spend HUNDRED in conditions.

2 Remove a back seat, address to Section Removal and installation of a back seat.

3 Remove a rubber epiploon-1 at the left or on the right under a seat. Cast away изоляционный a floor-mat.

4 Turn away screws of fastening and uncover-2.

The right gauge with the fuel pump:

5 Rasstykujte a socket-1. Thus release a clamp, having compressed it.

6 Mark a tape fuel hoses-2 and-3 and disconnect them from the stock gauge for what open collars.

The fuel system is under pressure, therefore a hose remove slowly and wipe the flowed out fuel.

7 Cautiously turn on blows накидную a nut-4. HUNDRED are applied for this purpose by tool BMW 161020. It can be carried out also by means of wooden бруска.

It is not necessary to apply the metal tool since thus probably formation of sparks.

8 Lift upwards the stock gauge, take him aside and take out. Thus enclose a rag and wipe the flowed out fuel.

The left gauge of a stock:

9 Turn away screws of fastening and uncover-2.

10 Rasstykujte a socket-1 gauges of a stock. Thus compress clamps.

11 Disconnect a fuel hose-2 from the stock gauge, for what ослабьте a collar-2.

The fuel system is under pressure, therefore the hose is necessary for removing slowly. If necessary wipe the flowed out fuel.

12 Cautiously turn on blows накидную a nut. HUNDRED are applied for this purpose by tool BMW 161020. It can be carried out also by means of wooden бруска.

It is not necessary to apply the metal tool since thus probably formation of sparks.

13 Lift the stock gauge, take him aside and take out. Press from the bottom party a clamp-1 and remove a levelling hose of a tank. Take out the gauge. Thus enclose a rag and wipe the flowed out fuel.



 INSTALLATION

Necessarily replace sealing rings of gauges of a stock.

The left gauge of a stock:

14 Be convinced that the return valve-1 is inserted into a levelling hose of a tank.

15 Insert the gauge and hold it approximately on 5 sm above a tank. Fix the gauge in a groove on a tank.

16 Level the gauge, having turned it. Thus the pad in the top part of the gauge should enter into a tank groove.
17 Put on and tighten накидную a nut. Thus the lock should enter a pad into a corresponding groove on a tank, distinctly having fixed.
18 Attach fuel hoses according to marks and fix their new collars.
19 Join штекерные connections and fix them.
20 Establish a cover and fix it, watching thus correct position of consolidation.
21 Insert into a cover a rubber epiploon. Will put back изоляционный a floor-mat.
22 Establish into place a back seat, address to Section Removal and installation of a back seat.
23 Attach a negative cable (-) the storage battery at the switched off ignition. Establish hours.

24 Check up work of the index of a stock of fuel on the panel of devices.

If the fuel tank does not manage to be emptied in the course of movement, it specifies that the tank equalizer between the right and left chambers incorrectly works. In this case it is necessary to remove at first the right gauge with the fuel pump. Then to remove the left gauge and to check up, whether the levelling hose-1 in a sediment bowl-2 is fixed. After check establish back both gauges.