BMW 3 series E46

Since 1998 of release

Repair and car operation



The BMW of 3 series Е46
+ Cars BMW 3 (Е46)
+ Current leaving and service
+ The engine
+ Systems of cooling, heating
+ Power supply systems, injection and release
+ Engine electric equipment
+ manual transmission and трансмиссионная a line
+ Automatic transmission
+ Coupling and power shafts
+ Brake system
- Suspension bracket and steering
   - Forward suspension bracket
      Removal and installation of an amortisation rack
      Dismantling of an amortisation rack/removal and shock-absorber/spring installation
      Shock-absorber check
      Shock-absorber recycling
      Removal and installation of the bearing of a wheel
      Removal and installation of a beam of a forward suspension bracket
   + Back suspension bracket
   + Steering with the hydraulic booster (сервоуправление)
+ Body
+ Onboard electric equipment
+ Electric equipment schemes





Removal and installation of an amortisation rack

 REMOVAL

Operation of lifting and car installation on supports is connected with danger! Therefore before operation carrying out familiarise with Razdelom Poddomkrachivanie and towage

1 Mark a paint position of a corresponding forward wheel concerning a nave. It will allow to establish at assemblage отбалансированное a wheel in its former position. Ослабьте bolts of fastening of a wheel at the car standing on the earth. Lift a forward part of the car, put it on supports and remove a forward wheel.

2 Take out a cable and a brake hose from the holder-1 on an amortisation rack.

3 Turn away bolts of fastening and remove a support with directing with a rotary fist and adhere a wire to a body, address to Section Removal and installation directing forward brakes.

Brake hose do not disconnect. Otherwise at installation it is necessary to delete air from brake system.

4 Cars with the xenon lamps: Remove a corner-1 angular hinges of adjustment of range of light from the cross-section lever-2.

5 Turn away a nut-1 качательной support-2 from an amortisation rack. Thus keep a wrench-3 for planes of a pin of the hinge.

6 Turn away a nut-1 and a tip of steering draught-2 from the rotary lever-3, address to Section Removal and installation of a tip of steering draught.

7 Turn away a nut-1 and remove the hinge-2 from the rotary lever-3 stripper, for example, HAZET 779-1.

8 Adhere the rotary lever a wire that it has not fallen.

9 Turn on on some turns a bolt-1 and remove the rotary lever-2 downwards from an amortisation rack-3.

10 If the rotary lever does not act in film (the bottom arrow), unclench шлиц the rotary lever and fix tool position. HUNDRED are applied to this purpose by special tool BMW-31-2-200 or KLANN KL-0101. Insert the tool in шлиц and turn on a corner 90 .

11 Prop up from below an amortisation rack the garage lift that it has not fallen at отворачивании the top fastening.

12 Turn away three nuts of fastening-1 support of an amortisation rack.

If in a support of an amortisation rack there is no aligning pin-2 or a corresponding aperture, it is possible to turn on only one nut. Probably mark position of a carving finger in relation to a wheel arch that after installation to keep former disorder of wheels more precisely.

13 Take out an amortisation rack from a wheel arch.


 REMOVAL

14 Cautiously insert an amortisation rack into a wheel arch. The aligning finger should enter into a corresponding aperture of a support of a rack. Screw on fingers new nuts and tighten their moment 25 Н•м.

If in a support of an amortisation rack there is no aligning pin-2 or a corresponding aperture, expose a rack it agree the marks put at removal.

15 Put on a rotary fist-1 an amortisation rack-2 so that the aligning pin-3 has entered in шлиц a rotary fist.

16 Put on a fist a rack against the stop and tighten a bolt the moment 80 Н•м.
17 Insert the hinge into a rotary fist and fix a new nut the moment 65 Н•м.
18 Connect a tip of steering draught to a rotary fist and tighten a new nut the moment 65 Н•м.
19 Fix качательную a support a new self-stopped nut the moment 65 Н•м on an amortisation rack. Thus keep a wrench a pin of the hinge from проворачивания.
20 Cars with the xenon lamps: Establish a corner for adjustment of range of light on the cross-section lever.
21 Press a cable and a brake hose with rubber support in the holder.
22 Establish a support, address to Section Removal and installation directing forward brakes.
23 Establish into place a forward wheel so that the marks put at removal have coincided. Preliminary grease with a thin layer подшипниковой greasings aligning belt of a disk of a wheel on a nave. Bolts of fastening of a wheel do not grease. Rusty bolts replace. Wrap bolts. Lower the car on wheels and tighten bolts cross-wise the moment 100 Н•м.