BMW 3 series E46

Since 1998 of release

Repair and car operation



The BMW of 3 series Е46
+ Cars BMW 3 (Е46)
+ Current leaving and service
+ The engine
+ Systems of cooling, heating
+ Power supply systems, injection and release
+ Engine electric equipment
+ manual transmission and трансмиссионная a line
+ Automatic transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
- Body
   The general information and security measures
   + Leaving and repair of damages of a body
   - External elements of a body
      Removal and installation of a forward bumper
      Removal and installation/check of shock-absorbers of a bumper
      Removal and installation of a back bumper
      Removal and installation of the back shock-absorber
      Removal and cover installation обтекателя
      Removal and installation of a forward wing
      Removal and cowl installation
      Cowl adjustment
      Removal and installation of a cover of a luggage carrier
      Adjustment of a cover of a luggage carrier
      Removal and installation of the lock/cylinder of the lock of a cover of a luggage carrier
      Removal and installation газонаполненного an emphasis of a cowl/cover of a luggage carrier
      Replacement молдингов and model emblems
      Removal, installation and door adjustment
      Removal and installation of facing of a door
      Removal and installation of the lock of a door
      Removal and installation of the cylinder of the lock
      Removal and installation of the external handle of a door
      Removal, installation and window adjustment
      Removal and installation electric стеклоподъемника
      Removal and electric motor installation стеклоподъемника
      Removal and installation of a mirror of an external kind / a sound signal of a high-pitch tone
      Removal and installation of glass of a mirror
      Removal and installation of the case of a mirror of an exterior
   + Internal elements of a body
+ Onboard electric equipment
+ Electric equipment schemes





Removal, installation and window adjustment

To have possibility of moving of a window of a door at the removed lateral pillow of safety, it is necessary to disconnect quickly a negative cable (-) the storage battery. Thereof in memory of malfunctions corresponding record is made. After work end it is recommended to clear memory thereby to provide normal work of a pillow of safety. Address to Section Diagnostics of malfunctions. Work it is desirable to spend HUNDRED in conditions.


 REMOVAL

1 Remove a lath of mine of glass-1. For this purpose protect a sticky tape-2 paint and varnish covering under a lath. Squeeze out a lath a plastic wedge-3 upwards from window mine. Thus, as is shown in an illustration, begin behind. In a forward part extend a lath under a mirror.

2 Remove facing of a door and uncover doors in a back part, address to corresponding section.

3 Open a window till the size And = 140 mm.

4 Turn out a bolt-1 back fastenings.

5 Turn out a bolt-2 forward fastenings.
6 Turn glass forward and take out from window mine.


 INSTALLATION

7 Insert glass from above into mine of a window and fix at стеклоподъемника screws-1 and-2.
8 If the old window is established, check up ease of its course moving upwards and downwards. If necessary adjust.


 ADJUSTMENT HAS FLOWN DOWN

9 Disconnect the back tyre стеклоподъемника-1. For this purpose ослабьте fastening of nuts-2 and-3, without turning on them. Preliminary remove hermetic from a nut-3.

10 Move glass with стеклоподъемником completely upwards.
11 Tighten nuts-2 and-3.
12 Some times move glass upwards and downwards, having checked up ease of its course. If necessary repeat adjustment.
13 Establish into place facing, address to corresponding section.
14 Establish an external lath of mine стеклоподъемника. That the lath slid is better, it is recommended to grease with its soap solution, for example, means for ware washing. Insert a lath in front under a mirror, then gradually press below into mine.