BMW 3 series E46

Since 1998 of release

Repair and car operation



The BMW of 3 series Е46
+ Cars BMW 3 (Е46)
+ Current leaving and service
+ The engine
+ Systems of cooling, heating
+ Power supply systems, injection and release
+ Engine electric equipment
+ manual transmission and трансмиссионная a line
+ Automatic transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
- Body
   The general information and security measures
   + Leaving and repair of damages of a body
   - External elements of a body
      Removal and installation of a forward bumper
      Removal and installation/check of shock-absorbers of a bumper
      Removal and installation of a back bumper
      Removal and installation of the back shock-absorber
      Removal and cover installation обтекателя
      Removal and installation of a forward wing
      Removal and cowl installation
      Cowl adjustment
      Removal and installation of a cover of a luggage carrier
      Adjustment of a cover of a luggage carrier
      Removal and installation of the lock/cylinder of the lock of a cover of a luggage carrier
      Removal and installation газонаполненного an emphasis of a cowl/cover of a luggage carrier
      Replacement молдингов and model emblems
      Removal, installation and door adjustment
      Removal and installation of facing of a door
      Removal and installation of the lock of a door
      Removal and installation of the cylinder of the lock
      Removal and installation of the external handle of a door
      Removal, installation and window adjustment
      Removal and installation electric стеклоподъемника
      Removal and electric motor installation стеклоподъемника
      Removal and installation of a mirror of an external kind / a sound signal of a high-pitch tone
      Removal and installation of glass of a mirror
      Removal and installation of the case of a mirror of an exterior
   + Internal elements of a body
+ Onboard electric equipment
+ Electric equipment schemes





Removal and installation of a forward wing

Observe instructions on carrying out кузовных works, address to Section the General information and security measures.


 REMOVAL

1 Disconnect a lath on a wing by means of wide plastic шпателя.
2 Remove the lateral repeater of turn, address to Section Replacement of lamps накаливания external illumination.
3 Remove a headlight, address to Section Removal and headlight installation.
4 Remove upward edge protection.
5 Mark a paint position of a corresponding forward wheel concerning a nave. It will allow to establish at assemblage отбалансированное a wheel in its former position. Ослабьте bolts of fastening of a wheel at the car standing on the earth. Lift a forward part of the car, put it on supports and remove a forward wheel.

6 Remove локер a wing at a longitudinal beam. For this purpose take out a small screw-driver clips-1 and-2.

At first take out a pin from the clip centre, and then take out a clip. The clip-2 on an illustration is closed by a lath.

7 Turn away a nut-3 and a bolt-4. Disconnect the bottom cover of an impellent compartment in a point-5, address to Section Removal and installation of the bottom cover of an impellent compartment.

8 Turn away bolts of fastening-1 and remove a forward peak of an arch of a wheel-2.

Turn out an additional bolt in a forward part from below. On an illustration the bolt is not visible.

9 Turn away bolts of fastening-4 локера a wing-3. Take out clips-5, thus at first take out pins, and then clips.

10 Open a door and through a crack turn away a fastening bolt (the marksman on an illustration) on a rack - And-.

11 Turn out three самореза in the length 22 mm-3 and one саморез in the length 19 mm-4.

12 Turn out the top screws of fastening Torx-2 wings-1. 5 – nuts from a sheet material.
13 Thanks to presence of a sheeting of the bottom the wing is reliably fixed. The hair dryer creating temperature not less 400С is necessary for a wing detachment.
14 Establish the hair dryer with a flat nozzle in the top and back area of a wing and soften a sheeting. After that remove from below in a forward part прилегания covered a sheeting. It important to make in the specified place, otherwise at removal the wing can вспучиться.
15 Remove a wing.


 REMOVAL

16 Clear adjoining surfaces of a wing, if necessary will correct.
17 If necessary coat a wing.
18 In places прилегания lay a usual sealing tape.
19 Establish a wing into place, will expose approximately and slightly fix bolts.
20 Will expose a wing, thus watch a uniform backlash in relation to a door and a cowl, address to Specifications.
21 Tighten all bolts of fastening of a wing.
22 Put on an internal surface covered a sheeting.
23 Fix bolts локер a wing and a forward peak of an arch of a wheel. Insert clips and press заподлицо pins.
24 Establish into place a forward wheel so that the marks put at removal have coincided. Preliminary grease with a thin layer подшипниковой greasings aligning belt of a disk of a wheel on a nave. Bolts of fastening of a wheel do not grease. Rusty bolts replace. Wrap bolts. Lower the car on wheels and tighten bolts cross-wise the moment 100 Н•м.
25 Put on from above an element of protection of edges.
26 Establish a headlight, address to Section Removal and headlight installation.
27 Establish the lateral repeater of turn, address to Section Replacement of lamps накаливания external illumination.
28 Put on a wing a lath.