BMW 3 series E46

Since 1998 of release

Repair and car operation


The BMW of 3 series Е46
- Cars BMW 3 (Е46)
   Identification numbers of the car
   Acquisition of spare parts
   Technology of service, the tool and the workplace equipment
   Поддомкрачивание and towage
   Start of the engine from the auxiliary power supply
   Checks of readiness of the car to operation
   Automobile химикалии, oils and greasings
   Diagnostics of malfunctions
   Controls and operation receptions
   Controls and devices
   Refuelling
   Keys, the uniform lock and anticreeping system
   Security сигнализация*
   Стеклоподъемники
   The hatch with podemno-sdvizhnoj крышкой*
   Seats
   Adjustment of position of a steering wheel
   Mirrors
   Safety systems
   The lock of ignition and engine start
   Lay brake
   Manual box of a gear change (manual transmission)
   Automatic transmission (АТ) *
   The lever of the switch of indexes of turn / a light signal
   Screen wipers and стеклоомыватели
   Heater of back glass
   Темпостат (automatics of maintenance of the set speed) *
   The alarm system of emergency rapprochement at a parking (PDC) *
   System of automatic stabilisation of stability with a regulator of a twisting moment of engine ASC+T/System of the dynamic control of stability DSC*
   The monitoring system of pressure of air in tyres (RDC) *
   Illumination and light devices
   Heater, ventilation and the conditioner of air of salon
   The salon equipment
   Обкатка
   Features of driving of the car
   The Katalitichesky converter
   Antiblocking system of brakes (ABS)
   Disk brakes
   Brake system
   Luggage spaces
   Automobile телефон*
   Readjustment of headlights
   Cowl
   Unlocking of a cover of the refuelling hatch manually
   Drive podemno-sdvizhnoj hatch covers вручную*
+ Current leaving and service
+ The engine
+ Systems of cooling, heating
+ Power supply systems, injection and release
+ Engine electric equipment
+ manual transmission and трансмиссионная a line
+ Automatic transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
+ Electric equipment schemes




Темпостат (automatics of maintenance of the set speed) *

Темпостат allows to remember and automatically to support demanded speed at level not below 30 km/h.

Inclusion темпостата

Темпостат can be included already after ignition key turn in position 1. Press the button 1. Thus on a control panel the control lamp will light up.
You can use темпостатом.

Movement with the set speed, storing of speed and dispersal

Press the button 2.

Actual speed of movement which will be supported by a constant is entered into memory темпостата. Each subsequent pressing of the button speed will increase by 1 km/h.

If to keep the button 2 in the pressed position the car will be dispersed without influence on an accelerator pedal. If to release the button, the speed reached to this moment remains in memory and will be supported at this level.

Delay

Press the button 3.

If before movement already occurred in a mode of maintenance of the set speed by each pressing of the button speed will decrease for 1 km/h.

If to keep the button 3 in the pressed position at movement in a mode of maintenance of the set speed degree of opening throttle заслонки automatically will decrease also movement it will be slowed down. If to release the button the speed reached to this moment remains in memory and it will be supported at this level.

Work interruption темпостата

At included темпостате press the button 1. The control lamp continues to burn. If necessary you can take advantage again темпостатом.

Besides, work темпостата automatically interrupts in following cases:

- At braking.
- At deenergizing of coupling or while translating the lever of selector AT from position D in position N.
- For BMW 318i, 320i, 323i, 328i: if the set speed is exceeded throughout more 30 with and more than on 16 km/h.
- For BMW 320d: if the set speed is exceeded throughout more 30 with and more than on 16 km/h or decreases more than for 20 km/h.

Call of speed from memory

Press the button 4.

There will be a call of last of the entered values of speed to which it at first will be finished, and then begins to be supported at the set level. With ignition key turn in position 0 темпостат it will be switched off, and the entered value of speed will be erased.

Deenergizing темпостата

Having interrupted work темпостата, once again press the button 1. The control lamp will go out, and the value of speed kept in memory will be erased.

To use темпостатом it is impossible, if the line abounds with turns or if the raised intensity of movement does not allow to move in regular intervals, and also on slippery (because of snow, a rain, ice) road or weak (gravel, sand) a ground.

If at movement under a bias of brake effect of the engine it is not enough, the set speed can be exceeded. On liftings probably its reduction if capacities of the engine do not suffice.